Reactor Mod FAQ

Why is my reactor Tank Leaking? How to re-fill reactor vape tank to prevent leaks?

If your rector or Tracer Mod Tank is leaking, please follow the following steps. Below is the correct process to fill your reactor and tracer tanks.

1. Close the Airflow Vent

2. Remove Cap from Tank

3. Fill the tank with VG Juice about ¾ of the way full.

4. Wipe off any excess juice from the cap area

5. Once filled, reattach the tank’s cap by lining up the threads and slowly twisting clockwise until snuggly fastened.

6. Turn Tank Upside down (mouthpiece facing down)

7. Open Air Vents

8. Tank is ready to use

 

 

How to turn on the Reactor Mod when I first receive it?

To turn the reactor battery, press the battery side-button 5 times rapidly. This will activate the battery

It is a good idea to turn it off before storing it although the battery does not just drain if it is left on.

 

Where to store Halo Reactor battery?

Store it safely in a dry place. Please avoid storing in a high temperature environment as it may cause damage to the battery and components.

 

How to adjust halo reactor wattage and voltage?

The reactor battery has up-down buttons in the front and a side button.

Wattage Adjustment:

  • Press the SIDE button 3 times to bring the Wattage Screen - only if VOLTAGE is showing on the LCD Screen
  • Use the Up-Down buttons to adjust the Wattage.

Voltage Adjustment:

  • Press the SIDE button 3 times to bring the Voltage Screen - only if Watt (XX W) is showing on the LCD Screen
  • Use the Up-Down buttons to adjust the Voltage.

Use lower voltage and wattage and gradually increase them.

 

How do I know how much battery is remaining and when to charge the reactor battery?

The LCD screen will show the battery. Battery can be charged at any time as you wish.

 

How to charge reactor battery?

Insert the smaller usb connector of the USB charging cable. The other end can be inserted into computer. Once connected to a power source, the battery level indicator on the LED screen will flash until fully charged. Once fully charged, the battery level indicator will stop blinking, shine for 10 seconds and go out.

 

What is the charging duration of reactor battery?

Normally 5 hours.

 

When to fill Reactor MOD Tanks?

Reactor tanks perform best when filled with at least 2 ml of E-liquid continuously. This ensures the heating element remains moist during use and will extend the overall life of the coil head. It is recommended that tanks be refilled once the E-liquid level drops below the top of the coil head.

 

How to fill Reactor Tank?

Refilling the Reactor tank is easy. First, unscrew the entire tank from the battery. Once removed, hold the tank with mouthpiece side down, and unscrew the Base from the Chamber by turning counter-clockwise. Next, hold the Chamber on a slight angle and pour eliquid into the tank along the glass side.

 

What type of E-Eliquid to use with Halo Reactor Mod?

The recommended type of e liquid is V-Type or VG Type E Liquids. Understand the difference between VG and PG E Liquid.

 

How to use Reactor Adjustable Air flow system?

The Reactor tank is equipped with an adjustable airflow system. To adjust airflow, twist the ring on the base hardware left or right to change the size of the air hole. A wider air hole creates a “looser” draw that results in cooler vapor. A narrow air hole creates a “tighter” draw with warmer vapor.

 

When to replace reactor coil head?

The Reactor tank is designed with a replaceable center coil head. This replaceable coil design offers significant cost savings over replacing the entire tank. If you experience a sustained burnt taste when vaping, or your tank is no longer producing adequate vapor, it may be time for a replacement. It is also recommended that you change your coils when switching between E-liquids to ensure there is no carry over of old flavors.

 

How to replace the Halo Reactor Coil Head?

Unscrew the entire tank from the Reactor battery. Once the tank is removed, hold the tank with mouthpiece side down, and unscrew the Base from the Chamber by turning counter-clockwise. Once the base is removed, the coil head will be exposed. Unscrew and remove the old coil head from the Base by turning counter-clockwise. Dispose of the old coil head, ensuring it is kept out of reach of children and pets. Attach a new coil head to the base by lining up the threads and turning clockwise until snug. The Base should then be re-attached to the Chamber by lining up the threads and turning clockwise until snug. After allowing 60 seconds for E-liquid to soak into the coil head, your tank is ready for use. The Rector Coils Can be bought separately - Click to get the Coild Heads.

 

How to clean Reactor Mod Tanks?

Your Reactor tank should be cleaned on a regular basis to remove any residue that may collect inside the chamber. It is also highly recommended that you clean the tank when switching between E-liquids to ensure there is no carry over of old flavors.

Halo Reactor Cleaning Instructions:

To thoroughly clean the Reactor tank, each individual component should be disassembled. First, unscrew the entire tank from the battery. Once removed, hold the Reactor tank with mouthpiece side down, and unscrew the Base from the Chamber by turning counter-clockwise. Dispose of any remaining E-liquid. Unscrew and remove the coil head from the Base by turning counter-clockwise. Dispose of the coil head, or place in a safe place for later use. Remove the mouthpiece and rinse all components (except for the coil head) under warm water until all E-liquid has been removed. A cotton swab may be used to remove any remaining liquid.